How do I reset my Datamax printer?

Table of Contents

Factory Reset

In the Desktop program RevolutionEHR Printing, access Utilities > Printer Diagnostics.
Select the appropriate Datamax printer.
Within the menu for Printer Diagnostics, access Printer Settings > Datamax > Restore Factory Defaults.
Click ‘Send.
Follow the instructions for Media Calibration.

How do I reset Datamax O’Neil E Mark III?

To Factory Default theDatamax E-Class Mark III Icon (‘Basic’ & ‘Advanced’) printer… Press and hold ‘Play / Pause’ button. After roughly 15 seconds, the Status (left) LED (see illustration, above) will start to flash ‘red’. Release the ‘Play / Pause’ button once the Status LED starts to flash ‘red’.

How do I find my Datamax printer IP address?

Connect the printer to your network

Connect a network cable to the Ethernet port on the back of the printer.
Turn the printer on using the power switch.
On the front cover of the printer is an X button.
The system report contains the IP address of the printer.

How do I connect my Datamax printer?

Installing Datamax Label Printer

Turn on your computer, and go to the Windows desktop. You should have an active internet connection, but do not launch WINK.
Plug your Datamax printer into an electric socket, and turn it on.
Using a Printer-USB cable, plug the datamax printer into one of your computer’s USB 2.0 ports.

What does Top of Form fault mean on a Datamax printer?

Problem Description. The printer could not find the TOF within the maximum label length setting, or TOF occurred in an unexpected place. Note. When using reflective media, this fault is given for an Out of Stock condition.

What is top of form fault?

Assuming that there is no mechanical problem with the printer, the error message indicates that there is a mismatch between the media sensor type and media (label) installed on the printer.

Who makes Datamax printer?

Honeywell
For over 50 years Datamax has created world class printers and printing supplies. Now a subsidiary of Honeywell, Datamax has multiple printers to aid any size organizations printing needs.

How do I calibrate my Datamax printer?

Quick Calibration > while the labels are installed press and hold the ‘Feed’ button for 10 seconds then release and at that point the printer should state “Calibration Complete” you might see the word pause on the printer display at that point press the ‘Pause’ button then the printer should state ready on its display.

How do you calibrate a Datamax E-Class printer?

To calibrate the Datamax E-Class Mark III Non-Display (‘Basic’ & ‘Advanced’) printer to its stock…

Power cycle the printer: turn it off, wait 30 seconds, and then turn it back on.
Wait for 30 seconds, to allow the printer to boot up completely.

Does the Datamax-O’Neil e-4204b Mark III support Windows programs?

The Datamax-O’Neil E-4204B Mark III supports the features below. Use true Windows printer Drivers by Seagull™ to use your Datamax-O’Neil E-4204B Mark III printer with any Windows program.

What is the size of a Datamax label?

Datamax-O’Neil Label(350966) 3″ x 3″ Direct thermal paper label. 500 labels/roll, 8 roll case. In Stock $128.44 + Add to Quote All Labelsfor the Datamax-O’Neil E-4204B » Recommended Ribbons Datamax-O’Neil Ribbon(IQRES-110300) IQRES RESIN RIBBON, 4.33″ x 984′, 1″ CORE, 48 rolls/case.

What is Datamax-O’Neil Ethernet printer cable used for?

Datamax-O’Neil Ethernet printer cable(UTP1400-10G) 10 ft. Ethernet printer cable with snagless RJ45 boots. Color: Green. Required for connecting Ethernet-enabled printers to a network. Global Supply Chain Constraints; Order now to be first when stock is available Datamax-O’Neil(MPU-4000) E-CLASS MARK III BATTERY PACK MOBILE POWER UNIT

What are the specs of the e-4204b label printer?

Desktop Label Printer, Honeywell-Datamax E-4204B, Direct thermal, 300 dpi, 5″ per Second Print speed, 4.16″ Print width, 64MBFlash, 32MB DRAM, Tear Edge, Adjustable Sensor, Serial and USB Interfaces, Includes US Power cord, NETIRA.